How about friends, I'm very happy, a lot of you are there, welcome to a new video
of my channel, That I fixed it, Dad, in this time the video that I bring you is
regarding the tools section for a handyman, let's do a review of
this tool .... a multimeter that I I think any handyman should have
At home, we started.
Well, in this review, I'm going to explain the technical characteristics
more basic than a handyman can get to use at home, since this
multimeter has many features and many applications that I surely
I will never use.
Well the model in particular that I have purchased is from PROSKIT brand and model
it's MT-1707 I think it's a model that for the price you have to
approximately between 30 to 40 euros, comes very complete
we are going to open it and ......
let's see how it comes.
As you can see, the book of instructions, which comes in English, with
which one I do not particularly benefit from it.
Here is the Tester, a clamp of quite quality, others that are
to measure the temperature ..... and to what about moisture
Surely it comes without a battery if we are going to mount them.
It carries four double batteries A
and already placed we have it ready for function.
The next step is to place the clamps, keep in mind that the position of
pegs is very important because if we we are wrong we can get to harm the
Tester then keep in mind that the black peg is the common one and that's always
it goes in the same position and the plug red I can connect it in three
positions, the one that I indicate in the image It is the most common, in that position we can measure:
voltage, both continuous, as alternate, ohms, hertz, diodes
temperature and some other thing. In this second position that I indicate
it is less usual for everyday use, here we can measure tensions up to
10 amps and in the third we can measure
micro amps is normally used by electronic
and now next I show you several everyday examples that we can measure
with this Tester, if we place the selector in 6 volts
continuous current, we can measure batteries which is a very common thing we have in
all the houses in this case it is a double A battery of 1.5 volts
let's check what load It has 1.18 volts, it is almost complete
the next thing I'm going to measure is a 12 volt drill battery, in this
case the range I have to move it to 60 volt direct current
and he says 10 volts what he means which is 80 percent of its load.
The next thing I'm going to measure is the current that we have in our homes
in this case it's alternating current, I'm going put the selector on 600 volts since
our current is 240 volts ... and it marks us a correct voltage.
Then he indicated more ranges than has this Tester that I'm not going to use.
In this position we can measure up to 10 amperes in alternating current and here you
I remember that you would have to change the red peg
and in the next position we could measure micro amps in current
continue as I mentioned earlier is the one chosen by the electronics and
we would also have to change our Red pin to the third location
here we could measure hertz
in this we can measure millifades
here we can measure temperature since this multimeter is quite complete
we would have to remove the tweezers normal and place the clamps with probe
the next position is very interesting since in this we can measure diodes and
shorts and the measurement is done by a beep or sound
and you could check if a circuit or piece are closed or short
in this case we are going to do a test with some automobile bulbs
As you can see in the video, the "BIP" indicates that the bulbs are correct
now in this position we can measure the resistance in ohms
It is specially designed to measure temperature and resistance probes
heating
I now as an example I will measure the resistance of a temperature probe
in this case the resistance that marks us varies according to the temperature that goes
acquiring the probe
Besides this multimeter has lighting on screen and one thing that I love
which is a led flashlight from behind
and at this point and only I there are two things that explain this
Tester, one is the subject of the temperature, as you can see in the image
we disconnected the normal clamps and we connect the clamps with probe
we place the selector in the position of thermometer
and we can already measure temperature, in this case I take the probe and it marks me 34 degrees ....
and finally I have left the position "NCV" if you have fixed this Tester
has a sensor in the top ... if we bring a cable and
This cable has tension, it indicates it to us ..... surprising truth? to me this function
has loved, because bringing the multimeter to any wall cable
tells us if it has current or not, without need to connect anything
incredible truth? .... good friends and as you have seen in the review I have tried to explain things
basic that a handyman may need of a multiplier ... as a product tell you that
I liked it a lot, both in materials, as in benefits, as in
price, without further ado I dismiss all Friday a video more and better see you
in the next because we are made a handyman first goodbye.
No comments:
Post a Comment